+86 1368264849

(+86)-020-88888888

Richupon usb cables manufacturers have 18 years experience in custom usb cables and usb data cable manufacturing.

USB cable wire inspection standards

by:Richupon      2020-08-12
USB cable wire is made up of what? Of course, is made up of PVC is and important copper wire. So we in the inspection of wire rod, especially pay attention to the test of copper wire, because the quality of the copper wire is often determines a USB cable quality is good and bad. So we quality strict inspection, to its specific inspection standards must be in strict accordance with the following steps: a, appearance inspection: must be put down the full of copper wire reel packaging on the stage, with one hand to take a piece of white paper on copper wire from 1 - The position of 2 cm, another hand will copper wire spool rolling week, visual whether its appearance to the following criteria: 1) Smooth surface, no black line, no line, no pitting, no oxidation, no flowers, no scratch, no tin (bruised Adhering tin, tin) , no slashes, no hand joint, no fingerprints. 2) Ribbon cable, uniform, no good, owe heap side ( Low on both sides of the high and low or high on both sides) , no stock. 3) Moderate tension but loose or too tight. 4) Copper wire surface after rolling no sticky ash ( A full) Second, the wire diameter inspection: wire diameter according to the national common standards, customers have special requirements according to its strict control. The specific inspection steps are as follows: 1) First, to debug the micrometer is zero. 2) , will test the copper wire clip wire, is put in the micrometer (use appropriate The strength of an overweight or underweight) Twist micrometer terminal. 3) , when they hear micrometer and observe the reading after three shaking. 4) And should be consistent and repeat test reading two or three times before ( The same piece of copper wire) Every time cannot detect the same position, should test section. 5) And wire diameter in 0. More than 2 cm of testing different interface of copper wire, copper wire to avoid a flat wire. Three, elongation test: elongation are in accordance with the national standard, when the customers have special requirements in accordance with the requirements for its strict control, the specific steps are as follows: 1) Open the elongation tester switch. 2) Observe whether its on the left side of the clip is in the original position, the instrument shows whether the reading of zero, such as induction on the left is not in the original position, the instrument shows reading is not zero, should immediately press the back button and the reset button. 3) Gently open the folder, put the test of the copper wire end in induction folder, pressure induction clamp, and then gently to copper wire straightening and put the other end in another induction folder, pressure induction to copper wire clip, press the test button. 4) After induction to copper wire tensile and stop moving, looking for the display reading is the detection of the elongation of copper wire. Four, resistivity test: resistivity requirements in accordance with the standards of country specific testing steps are as follows: 1) Open the resistivity tester power switch. 2) Clip on both sides of the induction of clamp, observe whether the reading to zero. 3) Shown in the instrument readings to 0, remove the wire from the upcoming inspection 1 m long with two clamp of induction on both ends of the wire, the detection of copper wire shall not contact with any metal items, press the test button. 4) Observe the display of readings, and take readings to the resistivity calculation, the calculation method is as follows: the resistivity = reading * * 0. 7854 * / 1000 five indoor temperature change coefficient, according to the above steps after the completion of the inspection, qualified chapter cover the QC.
is a must have for anyone who appreciates custom data cables to the greatest extent.
The Global custom made usb cables Leader. Richupon Industrial (Shenzhen) Company Ltd., will build a unique portfolio of Richupon and related brands, striving to surpass our competitors in quality, innovation and value, and elevating our image to become the custom made usb cables company most customer turn to worldwide.
If you need any help in custom made usb cables usb cable manufacturers, Richupon Industrial (Shenzhen) Company Ltd., can help you. We provide the best in class. Our design and services will enable you to create the ideal room that you have always wanted!
Custom message
Contact